新聞資訊
AZ31B鎂合金板材快速氣壓脹形行為
發布人：上海艾荔艾金屬材料有限公司www.jshcn.cn
更新時間：2015-12-13
對板厚1.0 mm的細晶AZ31B鎂合金板材進行快速氣壓脹形研究，在300~400 ℃的溫度范圍內進行了各種氣壓下300 s的快速氣壓脹形試驗，研究溫度和氣壓對AZ31B板材快速氣壓脹形能力的影響。
AZ31B鎂合金板材快速氣壓脹形行為Quick gas blow forming behavior of AZ31B magnesium alloy sheet
對板厚1.0 mm的細晶AZ31B鎂合金板材進行快速氣壓脹形研究，在300~400 ℃的溫度范圍內進行了各種氣壓下300 s的快速氣壓脹形試驗，研究溫度和氣壓對AZ31B板材快速氣壓脹形能力的影響。結果表明：在不同溫度下，脹形高度均隨著氣壓的升高而增大，但氣壓升高到一定程度時，脹形時間不到300 s即產生破裂；脹形高度在脹形溫度400 ℃時出現峰值為45 mm。在400 ℃和0.6 MPa條件下，脹形5 min時相對脹形高度達到1.13。脹形件壁厚分布不均勻，溫度越高，壁厚分布不均勻度越高。最后，研究了不同溫度下快速氣壓脹形時脹形件微觀組織的演變規律。
QGBF behavior for AZ31B magnesium alloy sheet with 1.0 mm thick was studied. Half-sphere free gas bulging tests were performed at 300?400 ℃ for 300 s duration to study the effects of temperature and gas pressure on QGBF properties of AZ31B sheet. The results show that the bulging height increases with the gas pressure increasing at different temperatures, however, the bulging parts crack within 300 s when the forming temperature exceeds the threshold. And the bulging height exists peak value at 400 ℃ reaches 45 mm and the highest specific height can reach 1.13 under the condition of 400 ℃ and 0.6 MPa for 5 min duration. The thickness distribution of bulging parts is uniform, and the higher the temperature, the larger the unevenness of thickness distribution. Furthermore, the microstructure revolution in the quick gas blowing process was discussed by observing the microstructure at different temperatures.
獲取更多我們供應的合金和服務信息，請致電086-021-67660801或發電子郵件kefu@ailiaigroup.com聯系我們，您也可以通過微博和微信和我們互動。
For more information on the alloys and services that we supply,?call us?at 086-021-67660801 or email us at kefu@ailiaigroup.com. You can also get in touch on social media, we are constantly active on?Weibo?and?Weixin.
前一頁：TC21鈦合金的熱壓縮變形行為及變形機理
后一頁：固溶時間對ZA72鎂合金顯微組織及力學性能的影響