新聞資訊
7A55鋁合金預拉伸板材的回歸再時效處理
發布人：上海艾荔艾金屬材料有限公司www.jshcn.cn
更新時間：2015-10-21
采用拉伸性能測試、慢應變速率拉伸測試、DSC分析、電導率測試及透射電鏡觀察，研究不同回歸再時效(RRA)處理制度對7A55鋁合金淬火預拉伸(W51)板材顯微組織、拉伸性能和抗應力腐蝕(SCC)性能的影響。
7A55鋁合金預拉伸板材的回歸再時效處理Optimum retrogression and reaging treatment of pre-stretched 7A55 aluminum alloy plate
采用拉伸性能測試、慢應變速率拉伸測試、DSC分析、電導率測試及透射電鏡觀察，研究不同回歸再時效(RRA)處理制度對7A55鋁合金淬火預拉伸(W51)板材顯微組織、拉伸性能和抗應力腐蝕(SCC)性能的影響。結果表明：采用120 ℃、24 h預時效，180 ℃、60 min回歸處理和120 ℃、24 h終時效的RRA工藝，可使7A55合金獲得與T6態相當?shù)膹?qiáng)度，而電導率大大提高，抗應力腐蝕性能接近T73態水平。7A55合金經適當?shù)腞RA處理后，晶內保持類似于T6狀態的顯微組織結構，為細小、彌散的η′相和極少量的η相；同時使晶界析出物的大小和分布特征與T73狀態類似，為呈斷續、孤立分布的粗化平衡相。
The effects of retrogression and reaging (RRA) treatment on the microstructure, tensile properties and resistance to SCC of a pre-stretched 7A55 aluminum alloy plate were studied by tensile test, slow strain rate tensile test, DSC analysis, conductivity measurement and transmission electron microscopy(TEM) observations. The results show that perfect mechanical and stress corrosion resistance properties can be obtained if the alloy is treated by the RRA of 120 ℃, 24 h pre-ageing, 180 ℃, 45 min retrogression and 120 ℃, 24 h re-aging. The strength of the alloy is almost the same compared with the T6 sample, while the conductivity increases greatly, and the stress corrosion resistance property enhances to the levels of T73 condition. Treated by proper RRA, small amount of η and a great mount of fine and dispersive precipitates η′ are observed in the matrix which is similar to that of T6 condition, while the coarse and discontinuous equilibrium precipitates are observed at the grain boundaries which is analogous to that of the T73 condition.
以上資料由上海艾荔艾金屬材料有限公司提供，歡迎新老客戶來電洽購。
本文來自上海艾荔艾金屬材料有限公司http://www.jshcn.cn，轉載請注明出處。