新聞資訊
高速線材軋制Ti-6Al-4V合金小規格棒材的熱處理工藝
發布人：上海艾荔艾金屬材料有限公司www.jshcn.cn
更新時間：2015-09-28
利用高速線材軋機制備Ti-6Al-4V合金小規格棒材(d10 mm)，研究固溶與時效熱處理工藝對棒材顯微組織與力學性能的影響。
高速線材軋制Ti-6Al-4V合金小規格棒材的熱處理工藝Heat treatment process of high-speed rollingsmall size Ti-6Al-4V alloys bar
利用高速線材軋機制備Ti-6Al-4V合金小規格棒材(d10 mm)，研究固溶與時效熱處理工藝對棒材顯微組織與力學性能的影響。結果表明：棒材組織主要由α相和β相組成，隨著固溶溫度從900 ℃升高到990 ℃，棒材中α相含量減少而β相含量逐漸增多，顯微組織出現了由初生等軸α相向針狀β相轉變進而向全片層狀β轉變的過程，棒材拉伸強度逐漸升高，而伸長率明顯降低；棒材在930℃固溶后進行時效處理，隨著時效溫度從450 ℃升高到650 ℃，β相轉變組織分解析出α相，組織主要由(α+β)相和β相混合組成，α相不斷集聚長大，使組織粗大，棒材抗拉強度降低，伸長率升高；經(930 ℃，30 min，水淬)+(550 ℃，4 h，空冷)熱處理后，棒材強度和塑性達到最佳配合，抗拉強度為1031 MPa，伸長率為12.5%。
The small size bars of Ti-6Al-4V alloys (d10 mm) were prepared by high-speed rolling. The effects of solution and aging heat treatments on the microstructure and mechanical properties of the alloy bars were investigated. The results show that the alloy bars are mainly composed of α phase and β phase. With the solution temperatures increase from 900 ℃ to 990 ℃, the content of primary α phase decreases and the content of β phase increases, the microstructure transform procedure is observed in the alloy with the primary equiaxed α phase to the needle plexiform transformed β phase, and then to full lamellar transformed β phase. Furthermore, the tensile strength of the alloy gradually increases and the elongation significantly decreases. When the alloy is treated at the solution temperature of 930 ℃ and then aged at temperature from 450 ℃ to 650 ℃, the transformed β phase constantly precipitates α phase, and the microstructure of the alloy is consisted of the (α+β) phase and β phase. Meanwhile, the α phase grows up, and then the microstructure becomes coarse. Furthermore, the tensile strength of the alloy decreases and the elongation increases. As a result, after the heat treatment of (930 ℃, 30 min, WQ)+(550 ℃, 4 h, AC), this alloy bars have optimum mechanical properties, the tensile strength is 1031 MPa and the elongation is 12.5%.
以上資料由上海艾荔艾金屬材料有限公司提供，歡迎新老客戶來電洽購。
本文來自上海艾荔艾金屬材料有限公司http://www.jshcn.cn，轉載請注明出處。