新聞資訊
AZ41M鎂合金動態再結晶臨界條件
發布人：上海艾荔艾金屬材料有限公司www.jshcn.cn
更新時間：2015-09-28
采用Gleeble-1500D型熱/力模擬試驗機在變形溫度300~450 ℃、應變速率0.005~1 s-1條件下對AZ41M鎂合金進行熱模擬壓縮試驗。用計算加工硬化率的方法處理試驗數據，再結合lnθ-ε曲線的拐點及–？(lnθ)/？ε-ε曲線最小值判據，建立合金熱變形過程中的動態再結晶臨界應變模型。根據熱壓縮實驗數據，分析溫度和應變速率等工藝參數對合金動態再結晶的影響。
AZ41M鎂合金動態再結晶臨界條件Critical conditions of dynamic recrystallization forAZ41M magnesium alloy
?采用Gleeble-1500D型熱/力模擬試驗機在變形溫度300~450 ℃、應變速率0.005~1 s-1條件下對AZ41M鎂合金進行熱模擬壓縮試驗。用計算加工硬化率的方法處理試驗數據，再結合lnθ-ε曲線的拐點及–？(lnθ)/？ε-ε曲線最小值判據，建立合金熱變形過程中的動態再結晶臨界應變模型。根據熱壓縮實驗數據，分析溫度和應變速率等工藝參數對合金動態再結晶的影響。結果表明：在該實驗條件下，AZ41M鎂合金的lnθ-ε曲線均具有拐點特征，對應的-？(lnθ)/？ε-ε曲線均出現最小值，該最小值所對應的應變即為臨界應變εc，得到合金臨界應變預測模型；臨界應變隨變形溫度的降低和應變速率的增加而增大，且峰值應變εp和臨界應變εc的比值滿足εp/εc?= 1.97。
The hot simulation compression tests of AZ41M magnesium alloy were conducted at deformation temperature in the range of 300-450 ℃ and strain rate in the range of 0.005-1 s-1?with the Gleeble-1500D thermal-mechanical simulation test machine. The critical strain model of dynamic recrystallization for AZ41M magnesium alloy during hot deformation was obtained by computing the work hardening rate θ from initial experimental data and combining with the inflection point criterion of lnθ-ε curves and the minimum value criterion of -？(lnθ)/？ε-ε curves. The influences of temperature and strain rate on the dynamic recrystallization were investigated based on the experimental data. The results show that an inflection point presents in the lnθ-ε curve and a minimum value appears in the corresponding –？(lnθ)/？ε-ε curve when the critical state of AZ41M magnesium alloy is attained, the strain that relates to the minimum value is the critical strain εc. The predicting model of critical strain is described. The critical strain increases with the decrease of deformation temperature and the increase of strain rate, and the ratio of peak strain (εp) and critical strain εc?is 1.97.
以上資料由上海艾荔艾金屬材料有限公司提供，歡迎新老客戶來電洽購。
本文來自上海艾荔艾金屬材料有限公司http://www.jshcn.cn，轉載請注明出處。
前一頁：固溶處理對Al-5.8Cu-0.6Mg-0.6Ag-0.3Nd合金組織和力學性能的影響
后一頁：焊后熱處理對Al-Mg-Si-Cu合金激光焊接接頭微觀結構和力學性能的影響