新聞資訊
Ti6321合金高溫變形行為及流動應力模型
發布人：上海艾荔艾金屬材料有限公司www.jshcn.cn
更新時間：2015-09-13
在Gleeble-1500型熱模擬壓縮機上對Ti6321鈦合金在溫度為850~990 ℃、應變速率為0.01~10.0 s-1、變形程度為60%的條件下進行了熱模擬壓縮實驗。
Ti6321合金高溫變形行為及流動應力模型High temperature deformation behavior and flow stress model of Ti6321 titanium alloy
在Gleeble-1500型熱模擬壓縮機上對Ti6321鈦合金在溫度為850~990 ℃、應變速率為0.01~10.0 s-1、變形程度為60%的條件下進行了熱模擬壓縮實驗。結果表明：Ti6321合金在變形開始階段，流動應力隨應變的增加迅速增加至峰值，隨著變形的繼續進行流動應力開始下降并逐漸趨于穩定；變形溫度升高和應變速率減小使峰值應力顯著降低。利用多元回歸分析建立Ti6321鈦合金在高溫變形時的流動應力模型，模型的計算值與實驗數據的平均相對誤差為6.59%，該模型較好地描述Ti6321鈦合金在高溫變形過程中的流動行為。
The isothermal compression of Ti6321 titanium alloy in the deformation temperature range from 850 to 990 ℃, the strain rate range from 0.01 to 10.0 s-1?and the deformation degree of 60% was conducted on a Gleeble-1500 isothermel compressor. The results show that the flow stress of Ti6321 titanium alloy increases quickly with the strain and reaches a peak, then decreases slowly to a near steady value. The peak stress significantly decreases with the increase of deformation temperature and decrease of strain rate. The flow stress model Ti6321 titanium alloy during high temperature deformation was established by using the regression method. The average relative difference between the calculated and experimental flow stress is 6.59%. The flow stress model can efficiently predict the deformation behavior of Ti6321 titanium alloy during high temperature deformation.
以上資料由上海艾荔艾金屬材料有限公司提供，歡迎新老客戶來電洽購。
本文來自上海艾荔艾金屬材料有限公司http://www.jshcn.cn，轉載請注明出處。
前一頁：Ti55鈦合金的熱壓縮變形及其本構方程
后一頁：熱軋溫度對Ti-45Nb合金棒材微觀組織及力學性能的影響