新聞資訊
高溫大氣和N2中Inconel690/1Cr13不銹鋼的微動磨損特性
發布人：上海艾荔艾金屬材料有限公司www.jshcn.cn
更新時間：2015-08-21
在試驗溫度為20~25 ℃(air)、300 ℃(air)、300 ℃(N2)，法向載荷為(Fn)50和100 N，位移幅值為60~200 μm的條件下，采用PLINT高溫微動磨損試驗機研究核電蒸汽發生器傳熱管材Inconel690與1Cr13不銹鋼圓柱配對副在滑移區的微動磨損特性。
高溫大氣和N2中Inconel690/1Cr13不銹鋼的微動磨損特性Fretting wear behavior of Inconel690 /1Cr13 stainless steel
in high-temperature air and nitrogen
在試驗溫度為20~25 ℃(air)、300 ℃(air)、300
℃(N2)，法向載荷為(Fn)50和100 N，位移幅值為60~200
μm的條件下，采用PLINT高溫微動磨損試驗機研究核電蒸汽發生器傳熱管材Inconel690與1Cr13不銹鋼圓柱配對副在滑移區的微動磨損特性。結果表明：當法向載荷一定時，隨位移幅值增加，在高溫大氣中，微動摩擦因數逐漸升高；而高溫氮氣中，摩擦因數降低。當載荷和位移相同時，Inconel690在高溫大氣中磨損較輕，在高溫氮氣中損傷較嚴重。在高溫大氣和高溫氮氣中磨痕表面均出現不同程度摩擦氧化，主要生成Fe、Ni、Cr等合金元素的氧化物。Inconel690的磨損機制主要表現為磨粒磨損、摩擦氧化和剝層磨損的共同作用。
The fretting wear behavior of the steam generator tubes
material Inconel690 of nuclear power was investigated against 1Cr13 stainless
steel by PLINT high temperature fretting tester in the slip regime under the
conditions of the temperatures of 20-25 ℃(air), 300 ℃(air) and 300
℃(N2), the normal loads of 50 and 100 N, and the displacement
amplitudes from 60 μm to 200 μm. The results show that the fretting friction
coefficient gradually increases as the increase of displacement amplitude under
the same normal load in the high-temperature air, however, the friction
coefficient decreases in the high-temperature nitrogen. The damage degree of
Inconel690 is slight in the high-temperature air, but more serious in the
high-temperature nitrogen at the same load and displacement. In the
high-temperature air and nitrogen atmosphere, the wear surface occurs different
degrees of friction oxidation which generates mainly oxidation of Fe, Ni, Cr and
so on. The abrasive wear, friction oxidation and delamination are main wear
mechanisms of Inconel690.
以上資料由上海艾荔艾金屬材料有限公司提供，歡迎新老客戶來電洽購。
本文來自上海艾荔艾金屬材料有限公司http://www.jshcn.cn，轉載請注明出處。